25.5×25.5mm Happymodel CrazybeeX FR/FS/PNP V2.2 F4 1-2S Flight Controller AIO 5A ESC 5.8G 25-200mW VTX & RX for Crux3 Trashcan Toothpick Whoop FPV Racing Drone

SKU: RC1767411

$77.67

Receiver FrSky Receiver / Receiver Flysky Receiver / Receiver Without Receiver /

Dispatch:Usually will be shipped in 24 hours
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Shipping Fast to Chat with us online to see if the product is in stock before order:
WhatsApp us

Notice:Will send it in new Version ( Comes with XT30 Connector).
All back order also send new version.
Beijing Time December 10th, 2020.
Introduction
CrazybeeX series flight controller is the first 5in1 AIO flight controller which could handle 2s.
It’s a better upgrade flight controller for your whoops.
– Use to build a 1-2S compatible lightest 65mm/75mm/85mm brushless whoop or 2-3 inch ultra light toothpick.
Specification
Brand:Happymodel
Model:CrazybeeX FR/FS/PNP V2.2
Item Name:F4 Flight Controller AIO ESC VTX Receiver Board
Weight:4.4g
Flight Controller:MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor:MPU-6000 (SPI Connection)
Board Size:28.5 * 28.5mm
Power Supply:1S-2S battery input (DC 2.9V-8.7V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky receiver support D8/D16 (
Built-in 5V 1A BEC
Built-in voltage detection
Firmware Target
CrazybeeX FR Version:Recommend Betaflight 3.5.7 target CRAZYBBEF4FR
CrazybeeX FS version:Recommend Betaflight 3.5.7 target CRAZYBBEF4FS
CrazybeeX PNP version:Recommend Betaflight 3.5.7 target CRAZYBEEF4DX
Onboard 5A 4In1 ESC:EFM8BB21
Power Supply:1-2S LiPo/LiPo HV
Current:5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory Firmware:S_H_50_REV16_7.HEX
Default Protocol:DSHOT600
(CrazybeeX FR V2.2 Version)
Onboard Frsky SPI Receiver:SPI BUS Receiver Frsky D8/D16 Compatible
Support for Futaba S-FHSS (Need Betaflight 4.0.5 firmware or latest), Frsky_X_LBT(EU-LBT)
Channels:8CH / 16CH
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground):100m~200m
(CrazybeeX FS V2.2 Version)
Onboard Flysky SPI Receiver:SPI BUS Receiver
Protocol:AFHDS and AFHDS-2A Switchable
Channels:8CH (AFHDS) or 14CH (AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground):100~200m
Failsafe support
(CrazybeeX PNP V2.2 Version W/O on Board Receiver):No Onboard SPI Receiver
Onboard 5.8G 40CH VTX:Output Power:25mw~200mw switchable
Frequency:40CH
Input voltage:3.3V 5.5V
Current consumption:300mA(type)
Frequency:5.8GHz 5bands 40 channels
With Race band
Smartaudio ready
Default vtx_power is 3
Should set vtx_low_power_disarm = ON to reduce the high temperature when test on the ground.
Onboard Voltage and Current detector:Voltage Meter scale “110”
Amperage Mete scale “1175”
Features
CrazybeeX FR V2.2 Bind procedure
Make the on board receiver get into bind mode:Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; Or use bind code to bind :For 3.5.7 version firmware Plug USB and then connect Betaflight configurator and then move to CLI tab , type “Frsky_bind”, the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.0.x the bind code is “bind_rx_spi” ,For 4.1.x or 4.2.x the bind code is “bind_rx”
Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink. The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio , but the bind is actually successful , need to go to CLI command and type “save” to finish the binding .
CrazybeeX FS V2.2 Bind procedure
Make the on board receiver get into bind mode:For 3.5.7 version firmware Press and hold the bind button for 1 second ,then plug USB, the Red LED at the bottom of the flight controller will blinking fast , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED at the bottom of the flight controller will blinking fast , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
Make your Flysky transmitter get into bind mode . If bind is successful the red led will getting to be solid.
SPI Receiver option
Frsky_D compatible with Frsky D8 protocol
Frsky_X compatible with Frsky non-eu D16 protocol
Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support)
SFHSS compatible with Futaba S-FHSS protocol
A7105_FLYSKY_2A compatible with Flysky AFHDS-2A protocol
A7105_FLYSKY compatible with Flysky AFHDS protocol
Package Included
1x CrazybeeX FR / FS / PNP V2.2 Version Flight Controller
1x Cale
1x bag of Screws & Standoffs

Weight 0.0044 kg

Reviews

There are no reviews yet.

Be the first to review “25.5×25.5mm Happymodel CrazybeeX FR/FS/PNP V2.2 F4 1-2S Flight Controller AIO 5A ESC 5.8G 25-200mW VTX & RX for Crux3 Trashcan Toothpick Whoop FPV Racing Drone”

Customers Also Viewed